Impulses on A.C. test voltages - generation and computer simulation
Read Online

Impulses on A.C. test voltages - generation and computer simulation

  • 181 Want to read
  • ·
  • 43 Currently reading

Published by UMIST in Manchester .
Written in English

Book details:

Edition Notes

StatementSupervised by: Cornick, K.J..
ContributionsCornick, K. J., Supervisor., Electrical Engineering and Electronics.
ID Numbers
Open LibraryOL19657719M

Download Impulses on A.C. test voltages - generation and computer simulation


Corpus ID: Simulation of Impulse Voltage Generator and Impulse Testing of Insulator using MATLAB Simulink @inproceedings{SheebaSimulationOI, title={Simulation of Impulse Voltage Generator and Impulse Testing of Insulator using MATLAB Simulink}, author={R. Sheeba and Madhavan Jayaraju and T. N. Shanavas}, year={} }.   Simulation of the high voltage impulse generator The most critical cases for the test object are a big capacitive load like a high voltage cables and power transformers with high inductance. For these reasons it is wise to support practical measurements by the simulations and to determine limits of a real by: 2. Purchase High Voltage Engineering - 1st Edition. Print Book & E-Book. ISBN , The impulse is applied to a test object to verify its capability of withstanding surges of high voltage and high current. In determining waveform for lightning impulse, there are many waveforms could be formed, such as 8/20 µs and 10/ µs. The most common used is 8/20 µs for impulse current surge and /50 µs for impulse voltage surge.

Design Requirements (1) To design a set of impulse voltage generator and generate impulse voltage wave Impulse waveform parameters: wave front time us Half-peak value time 36us (2) Please refer to the regulation High Voltage Test Techniques (edited by Tsinghua University) 3. R. Sheeba et al.: Simulation of Impulse Voltage Generator and Impulse Testing V 0(t 0 +δt 0) = v(t 0)+δt dV 0 dt t=t 0, V 0(t 0 +δt 0) = v(t 0)+δt dv(t) dt t=t 0. (2) Values of R d, R e, C z and C b can be obtained by using the above equations. Problem associated with impulse generator In the case of a 15 stages 3MV multi-stage, the capacitors are charged to kV from a regulator and. 62 M. Jayaraju & I. Daut & M. Adzman: Simulation of a novel ZVT technique based G. When the switch is ON (A= l) the voltage across the test object is given by (6), and when the switch is OFF (A= 0) the voltage is zero. The next step in the simulation process is to select the integration step. P.N. Nikolopoulos, Computer evaluation of impulse-current generator characteristics, Proc. 4th International Symposium on High Voltage Engineering, Athens, Greece, , paper High-Voltage.

High Voltage Engineering has been written for the undergraduate students in Electrical Engineering of Indian and foreign universities as well as the practising engineers. It deals in mechanism of breakdown of insulating materials, generation and measurement of high A.C., D.C., impulse voltages and currents. High voltage testing of some of the electrical equipments e.g. insulators, cables 3/5(4). However, it is found that measured value of signal SPD impulse limiting voltage fluctuates widely. The measured value of the same test object used in different pieces of equipment is very different. Even if the equipment and test object are the same, the measured value still varies greatly according to different test . The introduction to the full impulse voltages as defined in the previous section leads to simple circuits for the generation of the necessary wave shapes. The rapid increase and slow decay can obviously be generated by discharging circuits with two energy storages, as the wave shape may well be composed by the superposition of two exponential. Impulse voltages with an approximately linear rise are designated wedge shaped and those with a very steep front as steep-front impulse voltages [2]. Figure.4 Practical high voltage impulse generator Dentitions of impulse parameters of high-voltage impulses are somewhat different from those commonly adopted in.